VW T3 Transporter 1.9 Spark plug (92 hp Petrol SP)
Recommended part replacement interval for your car for the part category Spark plug: every 10.000 km / every 18 months
-
- Construction Year to: 10 / 1988
- Fuel Type: CNG / LPG
- Supplementary Article / Supplementary Info Info 2: Electrode gap must be set for operation on gas
- Replace after km: 15000
- Spark Plug: 1 - Earthed Electrode
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: 686S0012
- Manufacturer: RIDEX
- EAN number: 4059191685325
- Condition: New
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: 686S0010
- Manufacturer: RIDEX
- EAN number: 4059191451371
- Condition: New
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Product line: Nickel
- Spark Plug: Nickel-Copper Center Electrode, Nickel mass electrode
- Electrode Gap [mm]: 0,8
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Size: M 14 x 1,25
- Resistor [kOhm]: 6
- Spark Plug Head: Fixed SAE connector
- Item number: 686S0010P
- Manufacturer: RIDEX PLUS
- EAN number: 4066423771039
- Condition: New
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: 686S0069
- Manufacturer: RIDEX
- EAN number: 4059191571390
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Construction Year to: 10 / 1988
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 686S0070
- Manufacturer: RIDEX
- EAN number: 4059191571413
- Condition: New
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Size: M 14 x 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 686S0069P
- Manufacturer: RIDEX PLUS
- EAN number: 4069197952338
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Construction Year to: 10 / 1988
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 686S0070P
- Manufacturer: RIDEX PLUS
- EAN number: 4069197911168
- Condition: New
-
- Construction Year to: 10 / 1988
- Fuel Type: CNG / LPG
- Supplementary Article / Supplementary Info Info 2: Electrode gap must be set for operation on gas
- Replace after km: 15000
- Spark Plug: 1 - Earthed Electrode
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: SKSP-1990011
- Manufacturer: STARK
- EAN number: 4059191393190
- Condition: New
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: SKSP-1990009
- Manufacturer: STARK
- EAN number: 4059191393176
- Condition: New
- Spark Plug: with gasket seat, 3 - Earthed Electrode
- Electrode Gap [mm]: 0,8
- Spanner Size: 21
- Thread Length [mm]: 19
- for OE number: 101 000 007 AD
- contains article number: 13507
- External Thread Size: M14 x 1,25
- Item number: 13508
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816135081
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Size: M 14 x 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 0 242 235 663
- Manufacturer: BOSCH
- EAN number: 3165143134085
- Condition: New
-
- Construction Year to: 10 / 1988
- Fuel Type: CNG / LPG
- Supplementary Article / Supplementary Info Info 2: Electrode gap must be set for operation on gas
- Replace after km: 15000
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Size: M 14 x 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 0 242 240 592
- Manufacturer: BOSCH
- EAN number: 3165143134429
- Condition: New
- Product line: Q+, original equipment manufacturer quality
- Spark Plug: 1 - Earthed Electrode
- Electrode Gap [mm]: 0,7
- Construction Year to: 10 / 1988
- Length [mm]: 126
- Packaging width [cm]: 8,5
- Packaging height [cm]: 2,4
- Packaging Depth [cm]: 2,4
- Item number: V99-75-0011
- Manufacturer: VEMO
- EAN number: 4046001273643
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Spark Plug: with gasket seat, 3 - Earthed Electrode
- Electrode Gap [mm]: 0,8
- Spanner Size: 21
- Thread Length [mm]: 19
- for OE number: 101 000 007 AD
- External Thread Size: M14 x 1,25
- Item number: 13509
- Manufacturer: FEBI BILSTEIN
- EAN number: 4027816135098
- Condition: New
These products are designed to be used as originally These products are designed to be used as originally intended and not modified for purpose. Please ensure the intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. products are usually supplied without fitting instructions.
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Electrode Gap [mm]: 0,9
- Spanner Size: 20,8
- Supplementary Info: Super 4
- Thread Length [mm]: 19
- Spark Position [mm]: 5
- Thread Size: M 14 x 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 4
- Item number: 0 242 232 504
- Manufacturer: BOSCH
- EAN number: 3165141074321
- Condition: New
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Tightening angle [degrees]: 90
- Item number: SKSP-1990068
- Manufacturer: STARK
- EAN number: 4059191571383
- Condition: New
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- External Thread [mm]: 14
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Construction Year to: 10 / 1988
- Thread Pitch [mm]: 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: SKSP-1990069
- Manufacturer: STARK
- EAN number: 4059191571406
- Condition: New
-
- Construction Year to: 10 / 1988
- Required quantity: 4
- Electrode Gap [mm]: 0,8
- Spanner Size: 20,8
- Thread Length [mm]: 19
- Spark Position [mm]: 3
- Thread Size: M 14 x 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 1
- Item number: 0 242 235 909
- Manufacturer: BOSCH
- EAN number: 3165143506127
- Condition: New
price incl. 19% VAT
excl. delivery costs
- Electrode Gap [mm]: 0,9
- Spanner Size: 20,8
- Thread Length [mm]: 19
- Spark Position [mm]: 5
- Construction Year to: 10 / 1988
- Thread Size: M 14 x 1,25
- Tightening Torque [Nm]: 28
- Number of pins: 4
- Item number: 0 242 232 803
- Manufacturer: BOSCH
- EAN number: 4047026175165
- Condition: New
price incl. 19% VAT
excl. delivery costs
- Product line: Q+, original equipment manufacturer quality
- Spark Plug: 1 - Earthed Electrode
- Electrode Gap [mm]: 0,7
- Construction Year to: 10 / 1988
- Diameter [mm]: 25
- Length [mm]: 85
- Packaging width [cm]: 8,5
- Packaging height [cm]: 2,4
- Packaging Depth [cm]: 2,4
- Item number: V99-75-0004
- Manufacturer: VEMO
- EAN number: 4046001250248
- Condition: New
In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.
installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.
measurement, including photos.
For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.
When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.
If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
price incl. 19% VAT
excl. delivery costs
- 1
- 2