Valve, Tyre pressure control system, Tyre pressure sensor (tpms), Repair kit, Wheel sensor (tyre pressure control system) EV6T1A180CB

Complete unit for one wheel (sensor and valve) TPMS sensor needs to be programmed before use.

Complete unit for one wheel (sensor and valve) TPMS sensor needs to be programmed before use.

Complete unit for one wheel (sensor and valve) TPMS sensor needs to be programmed before use.

Complete unit for one wheel (sensor and valve) TPMS sensor needs to be programmed before use.

"Universal tyre pressure sensors from HELLA. *** HELLA Electronics OE competence for over 60 years. A wide range of vehicles can be covered with just one type o f sensor. Now available in different looks and colours. The sensor must be programmed and, if necessary, taught-in."

"Fully programmed and ready for installation! *** HELLA Electronics OE competence for over 60 years. No need for complex sensor programming. Significantly saves time in workshops!

Calibration by the corresponding vehicle manufacturers is al l it takes.

Complete unit for one wheel (sensor and valve) TPMS sensor needs to be programmed before use.

Herth+Buss wheel sensors can be used in all vehicles This snap-in wheel sensor can be installed in both light alloy rims and steel rims and can be activated that have a tyre pressure monitoring system installed as standard.The programming device AirGuard 95990001/- wirelessly. Please note that the permissible maximum 021 is required for the programming and adjustment of speed is restricted to 210 km/h. Supplied with a rubber valve. the sensors of each vehicle. This process only takes

between 5 and 15 seconds per sensor. An outstanding feature of the Herth+Buss wheel sensors: the original serial/ID number can be copied from the "old" sensor to the new one, or can be reassigned. In addition, the wheel sensors can be rewritten, and can be used in aluminium and steel rims. The sensors can be ordered individually and are supplied with a complete valve. A replacement valve is also available. • one for all: optimum stockage with just one universal wheel sensor • for steel or aluminium rims • certification up to 210 km/h • battery service life: 3-7 years • only programmable in connection with AirGuard 95990001/-021

Herth+Buss wheel sensors can be used in all vehicles that have a tyre pressure monitoring system installed as standard. The programming device AirGuard 95990001/- 021 is required for the programming and adjustment of the sensors of each vehicle. This process only takes between 5 and 15 seconds per sensor. An outstanding feature of the Herth+Buss wheel sensors: the original serial/ID number can be copied from the "old" sensor to the new one, or can be reassigned. In addition, the wheel sensors can be rewritten, used in aluminium and steel rims and wirelessly activated. The sensors can be ordered individually and are supplied with the complete valve in standard silver. A valve repair kit is also available, as are replacement valves in silver and black. • one for all: optimum stockage with just one universal wheel sensor • valves with adjustable angles • for steel or aluminium rims • certification up to 250 km/h • battery service life: 3-7 years • only programmable in connection with AirGuard 95990001/-021

Complete unit for one wheel (sensor and valve) TPMS sensor needs to be programmed before use.

Complete unit for one wheel (sensor and valve) TPMS sensor needs to be programmed before use.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale.

Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops.

Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list).

Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system.

Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.