Tyre pressure sensor (tpms) 52933F2000

EZ-Sensor 2.0 needs to be programmed to the correct vehicle before use.

EZ-Sensor 2.0 needs to be programmed to the correct vehicle before use.

Check compatibility of rim with sensor. Check compatibility of rim with sensor. Tightening torque for the valve insert: 0.4 Nm

Check compatibility of rim with sensor. Check compatibility of rim with sensor. Tightening torque for the valve insert: 0.4 Nm

EZ-Sensor 2.0 needs to be programmed to the correct vehicle before use.

"Universal tyre pressure sensors from HELLA. *** HELLA Electronics OE competence for over 60 years. A wide range of vehicles can be covered with just one type o f sensor. Now available in different looks and colours. The sensor must be programmed and, if necessary, taught-in."

"Universal tyre pressure sensors from HELLA. *** HELLA Electronics OE competence for over 60 years. A wide range of vehicles can be covered with just one type o f sensor. Now available in different looks and colours. The sensor must be programmed and, if necessary, taught-in."

"Universal tyre pressure sensors from HELLA. *** HELLA Electronics OE competence for over 60 years. A wide range of vehicles can be covered with just one type o f sensor. Now available in different looks and colours. The sensor must be programmed and, if necessary, taught-in."

A-Circuit; For 32mm OD slip ring; VR-B193MA for Voltage Set Clamp-In Valve for Direct-fit TPMS sensor For 32mm OD slip ring Negative & Positive Assembly Point: 15.0V; VR-B193MH for Voltage Set Point: 14.7V (Heavy Duty version); VR-B193ML for Voltage Set Point: 14.2V

"Fully programmed and ready for installation! *** HELLA Electronics OE competence for over 60 years. No need for complex sensor programming. Significantly saves time in workshops!

Calibration by the corresponding vehicle manufacturers is al l it takes.

Herth+Buss wheel sensors can be used in all vehicles This snap-in wheel sensor can be installed in both light alloy rims and steel rims and can be activated that have a tyre pressure monitoring system installed as standard.The programming device AirGuard 95990001/- wirelessly. Please note that the permissible maximum 021 is required for the programming and adjustment of speed is restricted to 210 km/h. Supplied with a rubber valve. the sensors of each vehicle. This process only takes

between 5 and 15 seconds per sensor. An outstanding feature of the Herth+Buss wheel sensors: the original serial/ID number can be copied from the "old" sensor to the new one, or can be reassigned. In addition, the wheel sensors can be rewritten, and can be used in aluminium and steel rims. The sensors can be ordered individually and are supplied with a complete valve. A replacement valve is also available. • one for all: optimum stockage with just one universal wheel sensor • for steel or aluminium rims • certification up to 210 km/h • battery service life: 3-7 years • only programmable in connection with AirGuard 95990001/-021

Herth+Buss wheel sensors can be used in all vehicles that have a tyre pressure monitoring system installed as standard. The programming device AirGuard 95990001/- 021 is required for the programming and adjustment of the sensors of each vehicle. This process only takes between 5 and 15 seconds per sensor. An outstanding feature of the Herth+Buss wheel sensors: the original serial/ID number can be copied from the "old" sensor to the new one, or can be reassigned. In addition, the wheel sensors can be rewritten, used in aluminium and steel rims and wirelessly activated. The sensors can be ordered individually and are supplied with the complete valve in standard silver. A valve repair kit is also available, as are replacement valves in silver and black. • one for all: optimum stockage with just one universal wheel sensor • valves with adjustable angles • for steel or aluminium rims • certification up to 250 km/h • battery service life: 3-7 years • only programmable in connection with AirGuard 95990001/-021