Lexus RX XU30 330 AWD Washer fluid jet, headlight cleaning (232 hp Petrol 3MZ-FE)

Flexible magnet lifter, 510mm, Øhead=13mm on hang tag •flexible shaft

•two component handle

•special tool steel

Application: HAZET Nozzle adjusting tool 4850-1 ∙ 670 mm Adjusting the nozzles of the windscreen washing systems

•The telescopic handle can be used to indicate the nozzle jet direction to the windscreen

•Magnetic head: 6 mm ∅

•Adjusting needle (∅ 0.7 mm) and protection cap

•With pocket clip

•Dimensions / length: 670 mm

•Length l1: 155 mm

•Net weight: 0.03 kg

Universal windshield removal device, 5 pcs •universal usage

•ideal for the correct and careful removal of adhered front windscreens as well as most rear and side screens

•with large guide rollers, which require less power and minimise the danger of wire snapping

•wire lead directly in front of the windscreen, therefore omitting the costly disassembly of trim parts in most cases

•easy one-man operation

•especially high-quality pump suction for secure windscreen holding

•suction power per disc up to 110 kg

•moveable suction disk also for heavily cambered screens

•in durable plastic storage case

Terminal device for gas pressure shock absorber, 30 mm •ideally suited for clamping weak or defective gas pressure dampers

•can be used on bonnets or boots

•for gas pressure shock absorbers up to 30 mm piston rod diameter

•aluminium

Products and spare parts supplied by us are only intended for the designated use. Installation may only be carried out by trained specialist personnel. Our products are not always supplied with installation instructions. Improper installation or inappropriate use may lead to the exclusion of warranty.

Products and spare parts supplied by us are only intended for the designated use. Installation may only be carried out by trained specialist personnel. Our products are not always supplied with installation instructions. Improper installation or inappropriate use may lead to the exclusion of warranty.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.