Opel Kadett E CC 1.7 D Suspension kit, coil springs / shock absorbers (57 hp Diesel 17 D)

"The minimum clearance between tires and suspension/body 23.) Send in front strut housings without wheel bearings, 41.) In the case of ordering complete struts these are only Height adjustable at the front axle only Lowering beyond the dimensions given in the type approval Please note additional information and vehicle-specific Wheel bearing diameter FA 64/66/72 mm? With or without ABS? ABS for may result in damage. These damages are not covered by H&R. parts is 5 mm. If the clearance is less than 5 mm, it has technical notes! 2.0 L 16 V, with wheel bearings dia. 72 mm and ABS brackets, cartridges etc. Damaged strut housings will be to be restored with wheel spacers or reworking brackets. Vehicles with bigger or either rejected or repaired for thebodywork. This bodywork and/or arising costs are not covered by H&R." extra charge if possible. In case of in advance delivery smaller wheel bearings (i.E. wheel bearing dia. 64 mm, 66 by H&R a desposit between 244 and 1200,- € per strut will mm, 74 mm) struts have to be sent in in advance. be required.

"The minimum clearance between tires and suspension/body 23.) Send in front strut housings without wheel bearings, 41.) In the case of ordering complete struts these are only Lowering beyond the dimensions given in the type approval Please note additional information and vehicle-specific RA hight ajustable ABS for may result in damage. These damages are not covered by H&R. parts is 5 mm. If the clearance is less than 5 mm, it has technical notes! 2.0 L 16 V, with wheel bearings dia. 72 mm and ABS brackets, cartridges etc. Damaged strut housings will be to be restored with wheel spacers or reworking brackets. Vehicles with bigger or either rejected or repaired for thebodywork. This bodywork and/or arising costs are not covered by H&R." extra charge if possible. In case of in advance delivery smaller wheel bearings (i.E. wheel bearing dia. 64 mm, 66 by H&R a desposit between 244 and 1200,- € per strut will mm, 74 mm) struts have to be sent in in advance. be required.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

For vehicles without ABS, a PowerDisc can be used on the rea r axle only if there is one on the front axle. The General Operating Permit (ABE) for the PowerDisc applies to operation on German roads in accordance with the German Road Traffic Registration Ordinance (StVZO). Other countries may require additional type approvals for use on roads.

For vehicles without ABS, a PowerDisc can be used on the rea r axle only if there is one on the front axle. The General Operating Permit (ABE) for the PowerDisc applies to operation on German roads in accordance with the German Road Traffic Registration Ordinance (StVZO). Other countries may require additional type approvals for use on roads.