Tyre pressure sensor (tpms) 407005DA0C

Complete unit for one wheel (sensor and valve)

"Universal tyre pressure sensors from HELLA. *** HELLA Electronics OE competence for over 60 years. A wide range of vehicles can be covered with just one type o f sensor. Now available in different looks and colours. The sensor must be programmed and, if necessary, taught-in."

After installing a new sensor, the TPM system must be reinit Complete unit for one wheel (sensor and valve) ialized/calibrated. The procedure refer to the owner's manua l of the car manufacturer.

Clamp-In Valve for Direct-fit TPMS sensor Negative & Positive Assembly

"Universal tyre pressure sensors from HELLA. *** HELLA Electronics OE competence for over 60 years. A wide range of vehicles can be covered with just one type o f sensor. Now available in different looks and colours. The sensor must be programmed and, if necessary, taught-in."

"Universal tyre pressure sensors from HELLA. *** HELLA Electronics OE competence for over 60 years. A wide range of vehicles can be covered with just one type o f sensor. Now available in different looks and colours. The sensor must be programmed and, if necessary, taught-in."

Herth+Buss wheel sensors can be used in all vehicles This snap-in wheel sensor can be installed in both light alloy rims and steel rims and can be activated that have a tyre pressure monitoring system installed as standard.The programming device AirGuard 95990001/- wirelessly. Please note that the permissible maximum 021 is required for the programming and adjustment of speed is restricted to 210 km/h. Supplied with a rubber valve. the sensors of each vehicle. This process only takes

between 5 and 15 seconds per sensor. An outstanding feature of the Herth+Buss wheel sensors: the original serial/ID number can be copied from the "old" sensor to the new one, or can be reassigned. In addition, the wheel sensors can be rewritten, and can be used in aluminium and steel rims. The sensors can be ordered individually and are supplied with a complete valve. A replacement valve is also available. • one for all: optimum stockage with just one universal wheel sensor • for steel or aluminium rims • certification up to 210 km/h • battery service life: 3-7 years • only programmable in connection with AirGuard 95990001/-021

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

"Fully programmed and ready for installation! *** HELLA Electronics OE competence for over 60 years. No need for complex sensor programming. Significantly saves time in workshops!

Calibration by the corresponding vehicle manufacturers is al l it takes.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

8.5 sec. LRC; B-Circuit Soft Start A-Circuit; For 28mm OD slip ring; VR-B194L for Voltage Set A-Circuit; For 32mm OD slip ring; VR-B193MA for Voltage Set For 32mm OD slip ring Point: 14.2V Point: 15.0V; VR-B193MH for Voltage Set Point: 14.7V (Heavy Duty version); VR-B193ML for Voltage Set Point: 14.2V

8.5 sec. LRC; B-Circuit Soft Start A-Circuit; For 32mm OD slip ring; VR-B193MA for Voltage Set For 28mm OD slip ring; VR-B195MA for Voltage Set Point: For 32mm OD slip ring 15.0V; VR-B195MH for Voltage Set Point: 14.7V; VR-B195ML for Point: 15.0V; VR-B193MH for Voltage Set Point: 14.7V (Heavy Duty version); VR-B193ML for Voltage Set Point: 14.2V Voltage Set Point: 14.2V