Actual offers of Turn signal light VW Golf VII Hatchback (5G1, BQ1, BE1, BE2) 1.5 TGI 130 hp Petrol/Compressed Natural Gas (CNG) DHFA

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

Replacement dynamic mirror turn indicator with ECE With up to 200% more brightness compared to standard certificate for all VW Golf VII models. mirror turn signals, high power LEDs, homogeneous light distribution, plug & play installation, ECE certified according to ECE R6/R10. High contrasts during day and night improve perception and consequently safety in road traffic.

Replacement dynamic mirror turn indicator with ECE With up to 200% more brightness compared to standard certificate for all VW Golf VII models. mirror turn signals, high power LEDs, homogeneous light distribution, plug & play installation, ECE certified according to ECE R6/R10. High contrasts during day and night improve perception and consequently safety in road traffic.

Regarding flasher lights with LEDs with active electronics

In connection with these low powers, which are very differen t from bulb versions, there can be problems with the bulb fa ilure check during operation on various traction vehicles. Since indicator failure checks are required by legislation, we recommend only operating the light in combination with an indicator control unit part no. "5DS 009 602-¿, 5DS 009 552-¿ or LED flasher unit 4.. 009 492". Operation of the light with alternating current or pulsed di rect current is not permitted! The individual light functions may only be operated with a v ehicle fuse of max. 3A.

Regarding single or double function lamps with LEDs without flasher function

In connection with these low powers, which are very different from bulb versions, there can be problems during operation on various traction vehicles because further lighting functions are detected by some traction vehicles. This is a vehicle comfort function which is not required by legislation and does not release drivers from their obligation to see for themselves that the lighting equipment is working. Here, too, faulty diagnoses can be a result of the lower power levels involved (instrument panel in the driver cab indicates a bulb failure although the function is working). The functional ability of these light failure checks can only be established by the vehicle manufacturer. Operation of the light with alternating current or pulsed direct current is not permitted! The individual light functions may only be operated with a vehicle fuse of max. 3A. In the case of onboard current limitation with the values specified above by the onboard control unit an additional fuse for the lamp is not required.