Nissan Almera n16 2.2 Di Crankshaft sensor (110 hp Diesel YD22DDT)

9.0276 9.0276 9.0276

Aluminum Heat Sink; M6 Battery Post With Diode Trio

1.953.276 1.953.276 1.953.276

These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use.

For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules.

If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at:

Phone: 040 - 25 30 66 55 Email: [email protected]

This often avoids extensive troubleshooting that is disproportionate to normal repair times.

The following applies to complaints: The more complete the processes are submitted, the faster they can be processed.

Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. the designated use. Please note that our products are usually delivered without Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use. unintended use.



measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. the designated use. Please note that our products are usually delivered without Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use. unintended use.



measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.