VW T6 Transporter 2.0 TSI Camshaft (204 hp Petrol CJKA)

Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use.

For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules.

If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at:

Phone: 040 - 25 30 66 55 Email: service@aic-germany.de

This often avoids extensive troubleshooting that is disproportionate to normal repair times.

The following applies to complaints: The more complete the processes are submitted, the faster they can be processed.

Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

In the warranty, we always make a distinction between wear Products supplied by us are without exception intended for parts and vehicle parts. All wear parts are subject to a the designated use. Please note that our products are usually delivered without reduced warranty period and a maximum mileage.

installation instructions. Brake components such as brake disks, brake pads, etc. Installation may only be carried out by trained specialist maximum of 1000 km (break-in period). Therefore, warranty personnel. claims for brake parts are only reviewed with an There is no guarantee for inappropriate, improper or installation invoice and a record of the wheel hub run-out unintended use.

measurement, including photos.

For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed.

When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced.

If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Application: HAZET Camshaft adjuster TORX® screwdriver socket ∙ with drilled hole 2788-T100H ∙ Square, hollow 12.5 mm (1/2 inch) Screw connection on camshaft adjuster

∙ Tamper-resistant TORX® profile ∙ T100H •Work on camshaft, timing chain or camshaft adjuster

•MERCEDES-BENZ: C-Class type 203 ∙ 204 ∙ 205 ∙ CLK 209 E-Class type 211 ∙ 212 ∙ E-Class Coupe type 207 SLK type 171 ∙ 172 G-Class type 463 ∙ Sprinter type 906

•Petrol engines: M133 ∙ 157 ∙ 176 ∙ 177 ∙ 270 ∙ 271 ∙ 271.8 ∙ 271.9 ∙ 272 ∙ 273 ∙ 274 ∙ 276 ∙ 278

•With knurling

•Surface: TIN coated

•Made in Germany

•Drive: Square, hollow 12.5 mm (1/2 inch)

•Output: Tamper-resistant TORX® profile

•Wrench size: ∙ T100H

•Dimensions / length: 100 mm

•Length l1: 60 mm

•For manual operation